DN | DASH | INCHES |
---|---|---|
6 | -4 | 1/4" |
8 | -5 | 5/16" |
10 | -6 | 3/8' |
12 | -8 | 1/2" |
25 | -16 | 1" |
31 | -21 | 1 1/4" |
*-16 and -20 may take up to 24 hours to from the time of order to complete
Viking Hoses & Fittings has a diverse inventory of Manuli Hoses and Fittings. One of the many advantages we have is we know hydraulic systems inside and out, literally. In many cases there are several options that will work for an application. We take serious responsibility in explaining the benefits of each option so that our customers confidently know they are leaving with the right hoses.
With a fully stocked inventory of Manuli hydraulic hoses and fittings we are confident that we have everything to meet your specific requirements. We offer all sizes ranging from 1/4″ to 1-1/4″, with options of low pressure, high pressure and conductive, and pressure washer hoses. Our hoses are top quality hoses that deliver maximum performance and efficiency for any type of equipment, brand or application.
Custom made Medium and High Pressure hydraulic lines for all hydraulic applications are available. All of our Manuli hoses have outstanding abrasion resistance, good for extreme temperature environments, and can be made for small or heavy duty equipment.
DN | DASH | INCHES |
---|---|---|
6 | -4 | 1/4" |
8 | -5 | 5/16" |
10 | -6 | 3/8' |
12 | -8 | 1/2" |
25 | -16 | 1" |
31 | -21 | 1 1/4" |
*-16 and -20 may take up to 24 hours to from the time of order to complete
Nonconductive hoses are used for minimum electrical resistance greater than one mega ohm per every inch of hose length at 1000 volts of DC. With nonconductive hoses they go through harsh work environments and can be used for air, oil, water, kerosene, and some chemicals. We can make and length hose you need quickly right at our shop.
DN | DASH | INCHES | WORKING PRESSURE |
---|---|---|---|
6 | -4 | 1/4" | 300 |
8 | -5 | 5/16" | 300 |
10 | -6 | 3/8' | 300 |
12 | -8 | 1/2" | 300 |
25 | -16 | 1" | 300 |
31 | -21 | 1 1/4" | 300 |
*-16 and -20 may take up to 24 hours to from the time of order to complete
If you need hoses for fuel transfer systems such as a tank truck, in-plant operation to transfer ethanol, gasoline, oil or petroleum based liquids we can make custom hoses to fit your needs. Fuel hoses are made to produce lower drag and abrasion resistance.
DN | DASH | INCHES | WORKING PRESSURE |
---|---|---|---|
6 | -20 | 1-1/4" | 250 |
8 | -24 | 1-1/2" | 250 |
10 | -32 | 2' | 200 |
12 | -40 | 2-1/2" | 200 |
Suction and discharge of diesel, ethanol, oil and petroleum based products up to 60% aromatic. Lightweight and extra flexible for road tanker discharge or In-plant applications. Excellent where applications demand the smallest bend radius.
Suction hose is great for for water, chemicals, and pumping services such as septic companies, agricultural, construction, marine and for irrigation services.
We build hydraulic hoses that meet the highest quality standards. We visually and dimensionally check every hose to ensure crimps to ensure the proper hose for your needs. We also institute a certified clean process to verify the absence of contaminants that could damage key hydraulic system components such as pumps and cylinders. We use Manuli hoses and they will exceed your expectations in terms of performance and longevity.
We can also perform fast and efficient hose repairs at our hose shop. Our repair process includes inserting a pneumatic foam projectile that will remove contaminants from inside the hose. We’ll also carefully measure coupling crimps to verify the appropriate diameter. Finally, we’ll cap off the hose ends to ensure the hydraulic fluids remain free of contaminants long after the repair job is done. We can typically complete this entire process in 30 minutes or less!